Registered Address: Environmental Science and Technology Ltd, 48 Thirkleby Way, York, North Yorkshire, United Kingdom, YO10 3QD. Phone: +44 (0) 1904 373018 Email: info@environst.com 

Company Number: 10773337

VAT Number: 270 6099 96

A Quick Guide to Maintaining your MiniRae 3000 and MiniRae Lite Photoionisation Detector (PID)

Asphyxiates | Toxic Gases | Volatile Organic Compounds (VOCs) | Benzene | Explosive gases | Atmospheric pollution | Dust/Particulates | Noise & Vibration | Weather | Ionising Radiation | Calibration and Service | Hire
 

 

Soil and water headspace sampling requires special attention beyond that needed for typical ambient air monitoring. Stripper effluents and soil vapour extraction streams are typically near 100% RH (relative humidity), and soil samples are often dusty and humid. Such conditions can cause high, drifting readings on many PIDs if not properly maintained. Interference is usually traceable to condensation in the sensor, causing a current leakage across the electrodes and thus a false-positive signal.

 

This situation is exacerbated when the sensor is contaminated by soil dust or condensed, high-boiling organic compounds.

 

The following steps will help you to maintain your PID:

 

a) Keep the sensor clean using high-purity methanol, preferably using an ultrasound bath. Flush the residual solvent from the sensor with a rapid stream of clean air, and clean the lamp housing area that contacts the sensor when in place.

 

b) On sensors with interdigital fingers, check that the metal electrode fingers do not contact the Teflon sensor walls. Bend them out carefully if necessary. Replace the sensor if the electrodes are corroded.

 

c) Keep the lamp clean using high-purity methanol. Never use acetone on 11.7 eV lamps.

 

d) Perform frequent changes of the dust filters (daily to monthly, depending on usage and dirtiness).

 

e) Use additional external filters (e.g., Teflon “water trap”) as an extra precaution, especially in dusty or moist environments. Once a - e are complete you will need to re-calibrate your unit. Please see the video below

 

f) Start sampling by using a dilution attachment, especially for highly contaminated soils. This minimises the amount of dust, water, and high-boiling organics condensing on the sensor and lamp. If the concentrations are too low to give a reading, remove the attachment to obtain an undiluted reading. Its important to remember, if you see anything around or over 1000ppm you are likely to have condensed VOCs on and in your PID and it'll need cleaning.

 

g) Avoid situations in which the PID is colder than the soil being sampled, such as heating the soil samples to increase the headspace organic concentration, or bringing a cold PID into a warm room without allowing time for temperature equilibration. If anything, try to keep the PID warmer than the soil samples. Otherwise you will create a condensing surface inside your PID and moisture will form on the sensor and lamp.

 

h) To obtain more stable readings, plumb the effluent flow from the PID back into the sample container to prevent diluting the sample. Use Teflon or metal tubing for this purpose so as to prevent adsorption to Tygon or other plastic tubing. Losses will not be stopped altogether but will be greatly reduced.

 

i) If humidity problems persist, use a humidity filtering tube to absorb moisture.

 

At Environmental Science and Technology (E.S.T.) we specialise in providing the highest standard of technology for purchase, hire, service and calibration. This means our customers only experience the best that industry has to offer, ensuring that you receive the greatest performance and reliability from your instruments. This allows your business to concentrate on the monitoring and control of environmental/workplace hazards.

 

 

 

MiniRae Lite Non-ATEX (059-A110-000) from £1,779 + VAT to £1,334.25 + VAT (Delivery at £18 + VAT)

Purchase the MiniRae Lite Non-ATEX PID monitor for 25% off. Perfect for soil head-space analysis and occupational hygiene spot checks where explosive atmospheres are not a risk! 

 

 

MiniRae Lite ATEX (059-A126-00) from £2,023+VAT to £1,517.25+VAT (Delivery at £18.00+VAT)

Purchase the MiniRae Lite ATEX PID monitor for 25% off. Perfect for soil head-space analysis, borehole testing and occupational hygiene spot checks! 

 

 

Share on Facebook
Share on Twitter
Please reload

Featured Posts

Contaminated Land, Does and Don'ts: Soil and Water Headspace Screening by PID

September 12, 2017

1/1
Please reload

Recent Posts